DIY camper van: 5 affordable conversion kits you can buy now | Ceiling Wall Panels

Over the course of my review run, I found the imaging performance of the 8C to be disappointing. Even in well-lit conditions, photos from the dual-lens primary camera setup come out to be vastly-overexposed, with details in brighter spots of the scene getting completely lost. Turning on HDR doesn’t help things either. The ‘Portrait mode’ generally works fine, allowing you to adjust the background blur even after the photo has been captured.

Unlike with most cases, the Atomic’s clear back is actually hard plastic. It’s fairly scratch-resistant, though it is smaller than most clear backs thanks to the aluminum surround. That being said, the cutout for the fingerprint sensor is still decently-sized, though there are two circular holes on the bottom for some reason. The buttons, despite being pushed as a feature, are ultimately a letdown. As far as I can tell, they’re metal, and the volume rocker even has arrows etched into it. However, they actually dig into your fingers since their edges aren’t rounded, and they’re very hard to push. I’m actually impressed at just how bad they are.

Bi-conductive surfaces were fabricated by embedding lines of a low-conductivity epoxy into a copper substrate. Copper sheets (1 mm thickness) were cut to size and grooves were machined into them using Wire Electrical Discharge Machining (EDM). The EDM wire thickness was 0.254 mm with a reported minimum spark gap of 0.381 mm ± 0.127 mm. The copper was then treated with an alkaline solution to produce an oxide layer with nano-scale surface roughness to promote adhesion between the copper and epoxy14. The surfaces were then coated with a non-conductive high-temperature two-part epoxy (Aremco 526N) filling all of the grooves. The epoxy was cured at 93 °C for 2 hours, followed by 163 °C for 12 hours to achieve a maximum strength bond. After curing, the surfaces were manually sanded with 200 grit sand paper until the bare copper between each epoxy division was exposed. The bare copper surfaces (with no epoxy divisions) were also sanded using the same method. The surfaces were finally cleaned with solvents and dried with N2.

Land Rovers have a reputation for off-road prowess, and the Velar’s stylish look doesn’t preclude it from getting muddy. An air suspension is standard on the V6 and optional of four-cylinder versions, and the system adds 1.5 inches (3.8 centimeters) to the ground clearance when at the maximum height, which takes the total to 9.88 inches (25.1 cm) with it. All-wheel drive and adaptive dampers also let the crossover get around when away from the pavement.

Coupe-inspired premium crossovers aim for a suave appearance, but the design often ends up looking awkward by trying too hard to mix utility with the sweeping rear of a true two-door. However, Land Rover’s new 2018 Range Rover Velar proves that fabulous styling is possible in the segment. The new vehicle will make a big premiere at the Geneva Motor Show and will also be on display in April at the New York Auto Show. Sales in the United States will start this summer.

Address: No.29, Hongxin Industrial Zone, Yuanhua Town, Hainingshi, Jiaxing, Zhejiang, China  (314400)

After 5,400 votes covering more than 100 products, the results for the inaugural “Best in Show” New Product Showcase Awards are in! The showcase provided NSC Congress & Expo exhibitors the opportunity to highlight their newest and most innovative safety products. Voting was available both online and onsite. The results are:

Enter this lovely home with a wood burning fireplace in the living room. There is an eat in kitchen and separate dining room with a bay window, also there is a main floor master bedroom. On the upper floor there are two more bedrooms and a full bath. There is a two car detached garage with a long driveway for more parking. This beautiful home is located in the Central West End, near Forest Park, universities and hospitals and transportation. Homes is being sold "As IS" sellers will do no repairs or pay for any inspections. Agent is related to sellers.

Hours after the joint committee’s vote, Womack and U.S. Rep. John Yarmuth, D-Ky., introduced the Bipartisan Budget and Appropriations Process Reform Act of 2018. It contains "the Joint Select Committee’s bipartisan recommendations relevant to the House of Representatives," the lawmakers said in a joint news release.

We report the counterintuitive mechanism of increasing boiling heat transfer by incorporating low-conductivity materials at the interface between the surface and fluid. By embedding an array of non-conductive lines into a high-conductivity substrate, in-plane variations in the local surface temperature are created. During boiling the surface temperature varies spatially across the substrate, alternating between high and low values, and promotes the organization of distinct liquid and vapor flows. By systematically tuning the peak-to-peak wavelength of this spatial temperature variation, a resonance-like effect is seen at a value equal to the capillary length of the fluid. Replacing ~18% of the surface with a non-conductive epoxy results in a greater than 5x increase in heat transfer rate at a given superheat temperature. This drastic and counterintuitive increase is shown to be due to optimized bubble dynamics, where ordered pathways allow for efficient removal of vapor and the return of replenishing liquid. The use of engineered thermal gradients represents a potentially disruptive approach to create high-efficiency and high-heat-flux boiling surfaces which are naturally insensitive to fouling and degradation as compared to other approaches.

Off-road mode increases the ride height by 1.8-in (46mm) compared to Normal mode at speeds below 32mph (50km/h) for a ground clearance of 9.9-in (251mm) and automatically lowers by 0.7-in (18mm) between speeds of 32-50mph (50-80km/h) to provide an ideal combination of stability, comfort and ground clearance during longer journeys on rutted, unpaved roads or surfaces.

MILAN — The lambent new tower of art galleries Rem Koolhaas and his Rotterdam-based firm, OMA, have designed for the Prada Foundation is a chameleon.